Life Fitness Treadmill 97TE User Manual

97Te, 95Te Tr eadmills  
As s e mb l y In s t r u c t io n s  
 
IMPORTANT SAFETY INSTRUCTIONS !  
¾ DO NOT position the rear of the treadmill within 6 feet ( 2 meters ) of the nearest obstruction. The  
sides of the treadmill should maintain a minimum clearance of 8 inches ( 20 cm ) from the nearest  
treadmill or other obstruction.  
¾ DO NOT locate the treadmill outdoors, near swimming pools, or in areas of high humidity.  
¾ DO verify the contents of the delivery carton against the accompanying parts listing prior to setting  
the cartons and shipping material aside. If any parts are missing, contact Life Fitness Customer  
Support Services at the number listed on the back page of this assembly instruction booklet.  
¾ Save the shipping cartons in case of return.  
¾ DO read the entire Operation Manual prior to attempting to operate this machine, as this is essential  
for proper use. The Manual explains how to properly use the treadmill and helps you to train your  
staff effectively.  
¾ NE placez PAS l’arrière du tapis roulant dans un rayon de 2 m (6 pi) de l’obstruction la plus proche.  
Les côtés de l’appareil ne doivent pas se trouver à moins de 20 cm (8 po) du tapis roulant voisin ou  
de toute autre obstruction.  
¾ NE placez PAS le tapis roulant à l’extérieur, près d’une piscine ou dans des endroits très humides.  
¾ VÉRIFIEZ si l’emballage contient toutes les pièces de la liste jointe avant de le mettre de côté. Si  
des pièces sont absentes, contactez l’assistance clientèle de Life Fitness au numéro indiqué au dos  
de cette brochure d’instruction de montage..  
¾ VÉRIFIEZ si l’emballage contient toutes les pièces de la liste jointe avant de le mettre de côté. Si  
des pièces sont absentes, contactez l’assistance clientèle de Life Fitness au numéro indiqué au dos  
de cette brochure d’instruction de montage.  
 
TOOLS REQUIRED FOR ASSEMBLY...  
Phillips screwdriver, Torx wrench, 3/4” combination wrench, flat blade screwdriver (or 5/16” nut  
driver)  
PARTS DESCRIPTION  
1
3
5
7
9
LEFT UPRIGHT  
Qty: 1  
Qty: 2  
Qty: 1  
Qty: 1  
Qty: 1  
2
RIGHT UPRIGHT  
Qty: 1  
HANDLEBAR (LEFT AND RIGHT)  
LEFT INSIDE HANDLEBAR SHROUD  
LEFT OUTSIDE HANDLEBAR SHROUD  
DISPLAY CONSOLE  
4
ERGO FRONT CROSSBAR  
Qty: 1  
6
RIGHT INSIDE HANDLEBAR SHROUD  
RIGHT OUTSIDE HANDLEBAR SHROUD  
Qty: 1  
8
Qty: 1  
10  
LOWER UPRIGHT COVER (LEFT AND RIGHT)  
0017-00101-1265  
Qty: 2  
11  
13  
15  
LEFT ACCESSORY TRAY  
HANDLEBAR CAP  
Qty: 1  
Qty: 2  
Qty: 6  
12  
14  
16  
RIGHT ACCESSORY TRAY  
Qty: 1  
Qty: 2  
Qty: 6  
REAR FRAME ENDCAP  
HANDLEBAR SHROUD SCREW  
0017-00101-1770  
ENDCAP / UPRIGHT COVER SCREW  
0017-00101-1772  
17  
19  
21  
23  
25  
DISPLAY CONSOLE / HANDLEBAR SUPPORT SCREW Qty: 6  
0017-00101-1773  
18  
20  
22  
24  
26  
SCREW GROMMET  
0017-00042-0326  
UPRIGHT MOUNTING BOLT  
0017-00101-1778  
FRONT CROSSBAR NUT  
0017-00103-0327  
UPRIGHT WASHER  
0017-00104-0335  
FRONT CROSSBAR GROMMET  
Qty: 2  
Qty: 4  
Qty: 4  
Qty: 4  
Qty: 2  
FRONT CROSSBAR SCREW  
0017-00101-1774  
ACCESSORY TRAY SCREW  
0017-00101-1780  
LINECORD CLIP  
0017-00042-0838  
Qty: 4  
Qty: 8  
Qty: 5  
Qty: 2  
UPRIGHT PLUG  
15  
16  
19  
17  
18  
20  
21  
22  
23  
24  
28  
1”  
2”  
3”  
4”  
5”  
 
IMPORTANT!  
DO NOT DISCARD THE SHIP KIT LOCATED ON TOP OF THE DECK AND BELT. ALL NECESSARY COMPONENTS  
NEEDED TO COMPLETE THE INSTALLATION ARE LOCATED IN THE SHIP KIT.  
IMPORTANT!  
NE JETEZ PAS LE KIT D’EXPÉDITION PLACÉ SUR LE DESSUS DU PLATEAU ET SUR LE TAPIS. IL CONTIENT TOUS LES  
ÉLÉMENTS NÉCESSAIRES POUR L’INSTALLATION.  
1. Remove the four SCREWS (A) securing the FRONT GRILL (B) to the  
E
FRAME (C). Remove the FRONT GRILL and set it aside.  
D
2. Remove the four SCREWS (D) securing the MOTOR COVER (E). Lift and  
remove the MOTOR COVER and set it aside.  
3. Locate the LEFT UPRIGHT (#1). Lay the LEFT UPRIGHT across the belt  
and deck with the notched end near the LEFT UPRIGHT MOUNTING  
BRACKET (F).  
B
4. Unwrap the CABLES (G) (Main Wire Harness, Coaxial Cable, and Ethernet  
Cable) leading from the LEFT UPRIGHT MOUNTING BRACKET (F). Feed  
the CABLES through the LEFT UPRIGHT (#1). Carefully tilt the LEFT  
UPRIGHT upwards and position the notched end of the LEFT UPRIGHT  
over the LEFT UPRIGHT MOUNTING BRACKET. With the LEFT TOP  
MOUNTING PLATE (H) directed forward, slide the LEFT UPRIGHT down  
over the LEFT UPRIGHT MOUNTING BRACKET and pre-installed BOLT  
and WASHER until it rests on the FRAME (C). Secure the LEFT UPRIGHT  
to the LEFT UPRIGHT MOUNTING BRACKET using two BOLTS (#20) and  
WASHERS (#24). One BOLT and WASHER on the inside of the LEFT  
UPRIGHT and one BOLT and WASHER on the front side of the LEFT  
UPRIGHT. Leave the BOLTS loose at this time.  
C
A
J
NOTE: BE CAREFUL NOT TO DAMAGE THE CABLES (G) WHEN  
ROUTING THEM THROUGH THE LEFT UPRIGHT (#1) OR WHEN  
SLIDING THE LEFT UPRIGHT OVER THE LEFT UPRIGHT MOUNTING  
BRACKET (F).  
H
G
2
NOTE: BE SURE THE PRE-INSTALLED WASHER IS ON THE OUTSIDE  
OF THE LEFT UPRIGHT (#1) WHEN SLIDING IT DOWN TO REST ON  
THE FRAME (C).  
5. Locate the RIGHT UPRIGHT (#2). With the RIGHT TOP MOUNTING  
PLATE (J) directed forward, slide the RIGHT UPRIGHT down over the  
RIGHT UPRIGHT MOUNTING BRACKET (K) and pre-installed BOLT and  
WASHER until it rests on the FRAME (C). Secure the RIGHT UPRIGHT to  
the RIGHT UPRIGHT MOUNTING BRACKET using two BOLTS (#20) and  
WASHERS (#24). One BOLT and WASHER on the inside of the RIGHT  
UPRIGHT and one BOLT and WASHER on the front side of the RIGHT  
UPRIGHT. Leave the BOLTS loose at this time.  
1
20 24  
20 24  
NOTE: BE SURE THE PRE-INSTALLED WASHER IS ON THE OUTSIDE  
OF THE RIGHT UPRIGHT (#2) WHEN SLIDING IT DOWN TO REST ON  
THE FRAME (C).  
K
20  
24  
C
6. With the bend of one HANDLEBAR (#3) directed to the outside of the  
treadmill, insert the HANDLEBAR into the RIGHT UPRIGHT HANDLEBAR  
BRACKET (L) as shown. Be sure the HANDLEBAR MOUNTING HOLES  
are aligned. Repeat for the left side HANDLEBAR.  
C
24  
F
7. Locate the ERGO FRONT CROSSBAR (#4) and position the ERGO  
FRONT CROSSBAR with the plastic SMART STOP COVER (M) facing  
upward and forward as shown. Locate and slide the left and right INSIDE  
HANDLEBAR SHROUDS (#5 & #6) over the corresponding ends of the  
ERGO FRONT CROSSBAR as shown. Slide the left and right INSIDE  
HANDLEBAR SHROUDS towards the center of the ERGO FRONT  
CROSSBAR as shown.  
M
6
26  
5
26  
19  
NOTE: BE CAREFUL NOT TO DAMAGE THE ANY WIRE HARNESSES  
THAT MAY BE LEADING FROM THE ENDS OF THE ERGO FRONT  
CROSSBAR (#4).  
L
22  
4
O
P
8. Install one FRONT CROSSBAR GROMMET (#26), rounded end first, over  
either end of the ERGO FRONT CROSSBAR (#4). Position the grommets  
just over the end brackets to meet the overmolding.  
N
3
22  
2
17  
NOTE: BE CAREFUL NOT TO DAMAGE THE ANY WIRE HARNESSES  
THAT MAY BE LEADING FROM THE ENDS OF THE ERGO FRONT  
CROSSBAR (#4).  
3
1
17  
 
M
6
26  
9. Position the right end of the ERGO FRONT CROSSBAR (#4) near the  
large access hole on the inside of the RIGHT UPRIGHT HANDLEBAR  
BRACKET (L).  
5
26  
Align the ERGO FRONT CROSSBAR MOUNTING HOLES with those in  
the RIGHT UPRIGHT HANDLEBAR BRACKET and secure using two  
BOLTS (#19), from the inside of the treadmill, and NUTS (#22). Tighten  
the BOLTS securely. Insert one SCREW (#16) from under the RIGHT  
UPRIGHT HANDLEBAR BRACKET. Tighten the SCREW securely.  
19  
L
22  
4
O
P
10. Position the left end of the ERGO FRONT CROSSBAR (#4) near the  
large access hole on the inside of the LEFT UPRIGHT HANDLEBAR  
BRACKET (N).  
N
3
22  
2
17  
Feed the SMART STOP CABLE (O) and HEART RATE CABLE (P) into  
the access hole downward out the bottom of the LEFT UPRIGHT  
HANDLEBAR BRACKET.  
3
1
17  
Align the crossbar mounting holes with those in the LEFT UPRIGHT  
HANDLEBAR BRACKET and secure using two BOLTS (#19), from the  
inside of the treadmill, and NUTS (#22). Tighten the BOLTS securely.  
Insert one SCREW (#16) from under the LEFT UPRIGHT HANDLEBAR  
BRACKET. Tighten the SCREW securely.  
NOTE: BE CAREFUL NOT TO PINCH THE SMART STOP CABLE (O)  
AND HEART RATE CABLE (P) (IF EQUIPPED) WHEN ASSEMBLING  
THE ERGO FRONT CROSSBAR (#4) TO THE LEFT UPRIGHT  
HANDLEBAR BRACKET.  
Feed the SMART STOP CABLE (O) and HEART RATE CABLE (P)  
upward through the top of the LEFT UPRIGHT (#1).  
11. Slide the LEFT INSIDE HANDLEBAR SHROUD (#5) near the LEFT  
UPRIGHT HANDLEBAR BRACKET (N).  
Locate and position the LEFT OUTSIDE HANDLEBAR SHROUD (#7) to  
match the LEFT INSIDE HANDLEBAR SHROUD.  
Secure the SHROUDS together using three SCREWS (#15). Tighten the  
SCREWS securely. Do not over-tighten the SCREWS. Repeat the  
procedure for the RIGHT INSIDE and OUTSIDE HANDLEBAR SHROUDS  
(#6 and #8).  
12. Locate the DISPLAY CONSOLE (#9). Remove the eight SCREWS (Q) from  
the back of the DISPLAY CONSOLE and separate the front of the DISPLAY  
CONSOLE from the rear. Position the REAR CONSOLE (R) over the LEFT  
and RIGHT TOP MOUNTING PLATES (H & J) as shown. From the bottom  
of the LEFT and RIGHT TOP MOUNTING PLATES, secure the REAR  
CONSOLE using four screws (#17). Tighten the SCREWS securely. Do not  
over-tighten the SCREWS.  
9
S
R
J
13. Position and rest the FRONT CONSOLE (S) facedown across the  
HANDLEBARS (#3). Connect all CONNECTORS leading from the LEFT (if  
equipped) and RIGHT UPRIGHTS (#1 & #2) to the corresponding  
CONNECTORS located on the FRONT CONSOLE. Feed any excess WIRE  
HARNESS into the UPRIGHTS. Carefully route all WIRE HARNESSES  
through the WIRE HARNESS GUIDES (T) located at the lower left of the  
REAR CONSOLE (R)  
H
Q
5
8
17  
14. Tilt the FRONT CONSOLE (S) upright and in position over the REAR  
CONSOLE (R). Secure the FRONT CONSOLE to the REAR using the  
previously removed eight SCREWS (Q). Tighten the SCREWS securely. Do  
not over-tighten the SCREWS.  
N
7
6
15  
3
NOTE: BE CAREFUL NOT TO PINCH THE ANY CABLES WHEN  
ASSEMBLING THE FRONT CONSOLE (S) TO THE REAR CONSOLE (R).  
3
2
T
1
R
1
 
15. Locate the LEFT ACCESSORY TRAY (#11). Carefully slide the tray into the  
top of the LEFT UPRIGHT (#1) as shown until fully seated. Secure the  
accessory tray to the LEFT TOP MOUNTING PLATE (H) using four screws  
(#21). Repeat the procedure for the RIGHT ACCESSORY TRAY (#12) and  
RIGHT TOP MOUNTING PLATE (J).  
11  
12  
16. Tighten all UPRIGHT BOLTS securely.  
17. Replace the MOTOR COVER (E) and secure the MOTOR COVER to the  
FRAME (C) using the four previously removed SCREWS (D). Tighten the  
SCREWS securely. Do not over-tighten the SCREWS.  
21  
18. Replace the FRONT GRILL (B) and secure the FRONT GRILL to the  
FRAME (C) using the four previously removed SCREWS (A). Tighten the  
SCREWS securely. Do not over-tighten the SCREWS.  
2
1
19. Locate one SCREW GROMMET (#18). Insert the SCREW GROMMET into  
the square hole located above the top inside mounting bolt of the RIGHT  
UPRIGHT (#2). Repeat for the remaining SCREW GROMMET and LEFT  
UPRIGHT (#1)  
20. Locate one LOWER UPRIGHT COVER (#10). Position the LOWER  
UPRIGHT COVER at the bottom notch of the RIGHT UPRIGHT (#2) making  
sure the top lip of the UPRIGHT COVER is engaged under the outside notch  
of the RIGHT UPRIGHT. Secure the UPRIGHT COVER to the RIGHT  
UPRIGHT using one SCREW (#16). Tighten the SCREW securely. Do not  
over-tighten the SCREW. Repeat the procedure for the LEFT UPRIGHT (#1)  
and remaining UPRIGHT COVER.  
2
16  
10 18  
21. Locate the UPRIGHT PLUGS (#25). Insert one UPRIGHT PLUG into each of  
the two access holes located on the lower outside of the LEFT and RIGHT  
UPRIGHTS (#1 & #2).  
22. Locate and press the HANDLEBAR CAPS (#13) over the ends of the  
HANDLEBARS (#3). Be sure the HANDLEBAR CAPS are fully seated.  
23. Using two SCREWS (#16) each, attach the two REAR FRAME END CAPS  
(#14) to the FRAME (C) as shown. Tighten the SCREWS securely. Do not  
over-tighten the SCREWS.  
24. Install the WAX BAG. Follow the instructions included in the WAX BAG KIT.  
25. Refer to the Operation Manual for power requirements, proper line cord  
routing, and other critical product information before connecting the treadmill  
to a power source.  
14  
C
16  
14  
 
PRE-OPERATION CHECKLIST  
Ensure that all fasteners are tight.  
Make sure the STRIDING BELT is properly tensioned and aligned according to the Operation Manual.  
Confirm the wax bag has been installed.  
Check the operation of the STOP switch and tether switch assembly.  
(See Operation Manual.)  
Confirm the display console is set to English or Metric units.  
(See Optional Settings ENG/MET in Operation Manual.)  
Refer to the Operation Manual for real time clock setting.  
Read the entire Operation Manual before using the treadmill.  
LISTE DES VÉRIFICATIONS À EFFECTUER AVANT LA MISE EN MARCHE  
Vérifiez si tous les dispositifs de fixation sont serrés.  
Assurez-vous que le TAPIS est bien tendu et aligné, conformément aux instructions du manuel  
d’utilisation.  
Assurez-vous que le sac de cire a été installé..  
Vérifiez le fonctionnement de l'interrupteur d'ARRÊT et reliez-le  
(cf. Manuel de l'utilisateur).  
Vérifiez si la console d’affichage est sur le système métrique ou anglais.  
(Référez-vous aux réglages facultatifs relatifs aux systèmes de mesure dans le Manuel de  
l’utilisateur.)  
Consultez le Manuel de l’utilisateur pour le réglage de l’horloge en temps réel.  
Lisez le Manuel de l’utilisateur dans son intégralité avant d’utiliser le tapis roulant.  
Before attempting to operate your Treadmill, it is imperative that you familiarize yourself with the contents of the  
Operation Manual. If your Life Fitness treadmill does not respond as described in the OPERATION MANUAL contact  
the nearest Life Fitness Service Center as listed in the OPERATION MANUAL.  
Life Fitness Customer Support Services  
(800) 351-3737 or (847) 451-0036  
Prior to your call, please be sure you have located and noted the  
MODEL NUMBER & SERIAL NUMBER.  
The Model & Serial number information of your Life Fitness Treadmill is contained in a label  
located on the front of the unit.  
©2004 Life Fitness, a division of Brunswick Corporation. All rights reserved. Life Fitness, Lifepulse, FlexDeck and Smart Stop are  
trademarks of Brunswick Corporation.  
Polar is a registered trademark of Polar Electro, Inc.  
MO51-00K58-A115  
1.04  
 

KTI Networks Network Card KF 221FX VerC User Manual
La Crosse Technology Marine Instruments WS 9009U IT User Manual
La Crosse Technology Portable Radio WS 7091UD User Manual
Lanzar Car Audio Stereo Equalizer E540P User Manual
LCD Digital Door DGP2 641 User Manual
Lexmark Air Conditioner 12EZ User Manual
Lincoln Electric Welder 4R90 User Manual
Listen Technologies Power Supply LA 205 User Manual
Lucent Technologies Telephone 6218 User Manual
Magellan Home Security System MGDCTXP2 TI04 User Manual