Lumenera Film Camera UBS 20 User Manual

QUICK START GUIDE FOR LUMENERA SKYnyx USB 2.0 CAMERAS  
Thank you for purchasing a Lumenera SKYnyx USB 2.0 camera. This camera is designed to operate straight out of  
the box. Please read these instructions in their entirety before proceeding, and then follow the steps below for a quick  
and easy installation.  
Required Tools and Parts:  
Computer:  
600 MHz or above Pentium compatible processor  
256 MB RAM memory  
USB 2.0 Port  
Operating System:  
Windows 2000 (Service Pack 3), or  
Windows XP (Service Pack 1)  
OPTIONAL - Power Connections for Lw-Based Cameras (Green LED):  
5 V DC regulated  
500 mA min. current  
2.1 mm tip, center positive  
Camera Set-up and Installation:  
Step 1 – Install 3rd party USB 2.0 PCI add-in card if your computer does not have a USB 2.0 port already. If you  
have purchased USB 2.0 PCI add-in card when you purchased your camera, the drivers for it are built-in when using  
Windows XP with Service Pack 1. Windows 2K users should first upgrade to Service Pack 3, and then go to the  
users should contact our Technical Assistance Center for current drivers before proceeding.  
Step 2 – Install camera software from the enclosed CD-ROM before connecting the camera to the computer.  
Insert the Lumenera Installer CD-ROM into your CD-ROM drive. The installer application should start automatically. If  
it does not, open a Windows Explorer window, locate the installer application on your CD-ROM drive and start it  
manually by double-clicking on the application. Follow the onscreen prompts to install the camera drivers.  
WARNING  
Observe the following to ensure smooth installation of camera software:  
You must ensure you are logged into the computer with administrator privileges prior to installing the camera  
software.  
Close all application software that is running and before inserting the Lumenera Installer CD into your CD-  
ROM drive.  
Do not connect the camera to the computer before installing the camera drivers.  
Step 3 – Connect the power supply to the camera if one was provided with your camera. Be sure to verify that your  
power supply meets the following requirements:  
Camera  
Voltage  
Lw-Based Camera (Green LED)  
5 V DC regulated  
Current  
500 mA minimum  
Connector  
2.1 mm tip, center positive  
WARNING  
Using an incorrect power supply may damage the camera and void the warranty.  
Step 4 – Connect the supplied USB 2.0 cable to the camera and a free USB 2.0 port on your computer.  
The Window’s New Hardware Wizard will pop-up detecting a new “Lumenera Unconfigured Device”. Select “Install  
the software automatically” from the options that are presented to you and click Next. A warning may appear notifying  
you that the drivers have not been digitally signed by Microsoft. Click Continue Anyway to continue with the driver  
installation. Then click Finish to install the drivers.  
Lumenera Corporation • 7 Capella Ct, Ottawa, ON, Canada K2E 8A7 • (t) 1.613.736.4077 • (f) 1.613.736.4071 • www.lumenera.com  
Technical Assistance Centre: support@lumenera.com  
©2006 Lumenera Corporation, all rights reserved.  
Design, features, and specifications are subject to change without notice  
V05162006  
 

Lenoxx Electronics Cassette Player 8980 FM User Manual
LG Electronics Microwave Oven LMV1683ST User Manual
Linear Smoke Alarm DXS 72 User Manual
Lochinvar Water System INS7141 User Manual
Logitech Universal Remote 1100i User Manual
Makita Drill 6176DW User Manual
McCall Refrigeration Refrigerator MCCF27 User Manual
McCulloch Trimmer MB 305 CBS User Manual
Metrologic Instruments Scanner TECH 8 User Manual
MicroBoards Technology CD Player CWR 424 52 User Manual